Jumat, 05 November 2010

Configurasi Static Router THE Packet Tracer

Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router0
fazza_Router0(config)#interface fastEthernet 0/0
fazza_Router0(config-if)#ip address 192.168.1.1 255.255.255.0
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router0(config-if)#exit
fazza_Router0(config)#interface serial 0/0/0
fazza_Router0(config-if)#ip address 10.10.10.1 255.255.255.252
fazza_Router0(config-if)#clock rate 64000
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
fazza_Router0(config-if)#exit
fazza_Router0(config)#interface serial 0/0/1
fazza_Router0(config-if)#ip address 10.10.40.2 255.255.255.252
fazza_Router0(config-if)#clock rate 64000
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router0(config-if)#exit
fazza_Router0(config)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
fazza_Router0(config)#ip route 192.168.2.0 255.255.255.0 10.10.10.2
fazza_Router0(config)#ip route 192.168.3.0 255.255.255.0 10.10.40.1
fazza_Router0(config)#

Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router1
fazza_Router1(config)#interface fastEthernet 0/1
fazza_Router1(config-if)#ip address 192.168.2.1 255.255.255.0
fazza_Router1(config-if)#no shutdown
fazza_Router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#interface serial 0/0/0
fazza_Router1(config-if)#ip address 10.10.10.2 255.255.255.252
fazza_Router1(config-if)#clock rate 64000
fazza_Router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#i
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to u
fazza_Router1(config)#interface serial 0/0/1
fazza_Router1(config-if)#ip address 10.10.20.1 255.255.255.252
fazza_Router1(config-if)#clock rate 64000
fazza_Router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router1(config-if)#exit
fazza_Router1(config)#interface fastEthernet 0/0
fazza_Router1(config-if)#ip address 10.10.50.2 255.255.255.252
fazza_Router1(config-if)#no shutdown
fazza_Router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router1(config)#ip route 192.168.1.0 255.255.255.0 10.10.10.1
fazza_Router1(config)#ip route 192.168.3.0 255.255.255.0 10.10.50.1
fazza_Router1(config)#ip route 192.168.4.0 255.255.255.0 10.10.20.2
fazza_Router1(config)#

Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router2
fazza_Router2(config)#interface fastEthernet 0/0
fazza_Router2(config-if)#ip address 10.10.50.1 255.255.255.252
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#interface fastEthernet 0/1
fazza_Router2(config-if)#ip address 192.168.3.1 255.255.255.0
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#interface serial 0/0/0
fazza_Router2(config-if)#ip address 10.10.30.2 255.255.255.252
fazza_Router2(config-if)#clock rate 64000
fazza_Router2(config-if)#no shutdown
fazza_Router2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to upe
% Ambiguous command: "e"
fazza_Router2(config-if)#exit
fazza_Router2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
fazza_Router2(config)#interface serial 0/0/1
fazza_Router2(config-if)#ip address 10.10.40.1 255.255.255.252
fazza_Router2(config-if)#clock rate 64000
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
fazza_Router2(config)#ip route 192.168.1.0 255.255.255.0 10.10.40.2
fazza_Router2(config)#ip route 192.168.2.0 255.255.255.0 10.10.50.2
fazza_Router2(config)#ip route 192.168.4.0 255.255.255.0 10.10.30.1
fazza_Router2(config)#


Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router3
fazza_Router3(config)#interface fastEthernet 0/0
fazza_Router3(config-if)#ip address 192.168.4.1 255.255.255.0
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router3(config-if)#exit
fazza_Router3(config)#interface serial 0/0/0
fazza_Router3(config-if)#ip address 10.10.20.2 255.255.255.252
fazza_Router3(config-if)#clock rate 64000
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
fazza_Router3(config-if)#exit
fazza_Router3(config)#interface
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
% Incomplete command.
fazza_Router3(config)#interface serial 0/0/1
fazza_Router3(config-if)#ip address 10.10.30.1 255.255.255.252
fazza_Router3(config-if)#clock rate 64000
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router3(config-if)#exit
fazza_Router3(config)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
fazza_Router3(config)#ip route 192.168.2.0 255.255.255.0 10.10.20.1
fazza_Router3(config)#ip route 192.168.3.0 255.255.255.0 10.10.30.2
fazza_Router3(config)#






Diposting oleh di

Tidak ada komentar:

Posting Komentar

Langganan: Posting Komentar (Atom)